FAQ & troubleshooting

Quick answers for newcomers, and fixes for the most common problems.

The basics

Do I need a license to use Meshtastic or MeshCore?

In the US, these radios normally run on 915 MHz in an unlicensed band, so most people do not need a license for ordinary use. Ham radio and GMRS are separate services with their own rules: see the ham and GMRS pages. Operating under amateur rules on the same band adds requirements, such as limits on encryption. This is general information, not legal advice. If you are unsure, check the FCC rules or ask a local club.

Should I start with Meshtastic or MeshCore?

Both have local channels here. Meshtastic is usually the easier start and supports more hardware. MeshCore relies on dedicated repeaters and suits planned community networks. Many people try both. One radio runs only one firmware at a time, but you can reflash it. See the comparison.

Can Meshtastic and MeshCore nodes talk to each other?

No. They are separate protocols. You need a Meshtastic radio to reach Meshtastic users and a MeshCore radio to reach MeshCore users.

How far will my messages go?

It depends mostly on height and what is between radios. Hills, buildings, and trees block signals. Indoors, expect short range. From a high outdoor spot with a clear view, much farther. Relaying through other nodes extends reach. See the placement guide.

Do I need my phone?

Most radios need an app on a phone or computer to read and send messages. Some devices with a built-in screen and keyboard work on their own, such as the LILYGO T-Deck for Meshtastic and the standalone devices listed on meshcore.io for MeshCore.

Is there a monthly fee?

No. You buy the hardware once. There is no subscription or carrier.

Can I count on it in an emergency?

Treat it as a backup for short text messages when cell service is down. There is no guarantee that anyone is listening or that a message arrives. If you can, call 911 first. See the ham and GMRS pages for voice options.

Troubleshooting

I can't see any other nodes.
  1. Check that the antenna is attached and the radio is charged. Never power a radio on without its antenna.
  2. Meshtastic: set the region to US and the modem preset to Medium Fast. All nodes must share the same region, preset, and frequency slot. New radios often start on Long Fast (or Long Turbo on some newer firmware), which cannot hear Medium Fast. Meshtastic also picks the frequency slot from the primary channel's name, so if you renamed your primary channel your radio may be on a different frequency than local nodes. See the Meshtastic setup.
  3. MeshCore: choose the USA radio preset in the app. See the MeshCore setup.
  4. Move to a window, outdoors, or higher up. Concrete, metal, and low-e glass block radio.
  5. Wait. Nodes announce themselves from time to time, so the list can take a while to fill.
  6. Ask in local chat whether anyone nearby is on the air. See the St. Paul page.
Nodes show up, but my messages don't go through.
  • On Meshtastic, a channel message counts as delivered once any node repeats it. That does not prove the person you meant received it. Test with a direct message.
  • Check the channel name and key exactly. Capitalization matters.
  • Leave the Meshtastic hop limit at the default of 3. Raising it tends to cause congestion.
  • MeshCore companions do not relay other people's messages (unless you have deliberately turned on the separate off-grid repeat mode, which you should not do on the public mesh). Out of direct range, you need a repeater within reach.
  • Busy channels get congested. Keep messages short and try again in a minute.
Bluetooth won't pair or keeps disconnecting.

Only one phone or app can connect to a radio at a time. Remove (“forget”) the radio in your phone's Bluetooth settings, restart the radio and the app, then pair again from inside the app. Enter the PIN shown on the radio's screen if asked. Radios with no screen usually use the default PIN 123456. Make sure the app has Bluetooth permission, and update the app and firmware.

Flashing the firmware fails.
  • Use Chrome or Edge on a computer. Phones and some other browsers won't work.
  • Use a USB cable that carries data. Charge-only cables will not work.
  • Try another USB port or cable.
  • Many boards need to enter download mode. This is often done by holding the board's BOOT or PRG button while plugging in USB. Check your board's documentation.
  • If a radio seems dead after a failed flash, flash it again from the web flasher.
The QR code won't scan, or the channel won't add.

Show the QR code on another screen or a printout. You cannot scan it from the phone that is displaying it. If it still fails, enter the channel by hand. For MeshCore, the name is West Seventh (capital W, capital S, one space) and the secret is 32 letters and numbers with no spaces. Use the copy buttons on the St. Paul page to avoid typos, and update the app if the option is missing.

My battery drains fast, or the radio gets hot.
  • The screen, GPS, and Bluetooth use a lot of power. Dim the screen and turn off GPS if you don't need it.
  • Cold weather cuts battery capacity. Solar nodes in a Minnesota winter need generous battery capacity and a battery rated for cold charging.
  • A little warmth while charging is normal. If a battery is very hot or swollen, unplug it, stop using it, and dispose of it safely.

Privacy and safety

Who can read my messages?

Anyone with the channel's key. Public channels use publicly known keys. The West7th and West Seventh keys are posted on this site, so treat those channels as public. For private conversations, create a channel with your own secret key and share it in person. Encryption does not make you anonymous: node names and the fact that you transmitted can still be seen.

Is my location shared?

Only if you turn it on, but check. On Meshtastic, sharing position on a channel sends your coordinates to everyone on that channel. Connecting to the public MQTT server can publish node locations to the internet. Review your position and MQTT settings, and reduce precision or turn them off if you don't want to be found.

Should I use my real name for my node?

You don't have to. A nickname is fine. Avoid putting your address, phone number, or other private details in a node name.

Are these radios safe to use?

They are low-power radios. As a habit, keep the antenna away from your face, and never transmit without an antenna attached because it can damage the radio. Follow the safety notes before mounting anything outdoors.

Can I run a repeater or router?

You can, but it needs thought. Poorly placed repeaters make a network worse. Read the placement guide and etiquette, and talk to the local group first.

Still stuck? Ask in local chat (see the St. Paul page) and tell us your radio model, firmware version, and what you have tried.

Sources

These pages are general guidance gathered from project documentation and community sources, last reviewed November 17, 2026. Firmware and apps change, so check each project's current docs.