RTL-SDR: listen to the radio world for about $40

An RTL-SDR is a small USB stick that turns a computer or Android phone into a radio receiver for a huge range of signals: aircraft, weather satellites, ham repeaters, NOAA weather radio, FM stations and much more.

What it does, in plain English

A normal radio is built to hear one kind of signal, like FM music. An RTL-SDR (software-defined radio) is different: the USB stick just captures a slice of the radio spectrum, and software on your computer does the rest. Change the software and the same stick becomes an aircraft tracker, a weather satellite receiver or a police and fire scanner for unencrypted channels.

The name comes from the Realtek RTL2832U chip. It was designed for watching TV on a laptop, until people discovered it could tune almost anything from about 500 kHz to 1.7 GHz.

It only receives. An RTL-SDR cannot transmit, so you don’t need a license to use one. The rules on what you may listen to are covered below.

The waterfall is the heart of SDR software: a scrolling picture of the spectrum where every signal shows up as a bright line. Click a line and you are tuned to it.

What to buy

These are Amazon affiliate links. Every affiliate purchase helps the St. Paul Radio Authority provide radios to the community at no cost, and receipts are available on request. See our disclosure.

RTL-SDR Blog V4 kit

The dongle most people should start with. The kit includes a telescoping dipole antenna, a suction-cup mount and cables.

Start here. Covers roughly 500 kHz to 1.7 GHz.

See on Amazon →

Nooelec NESDR Smart v5

A well-built alternative dongle in an aluminum case, often sold as a kit with antennas.

See on Amazon →

FlightAware Pro Stick Plus

An RTL-SDR with a built-in filter and amplifier for 1090 MHz. The easy choice for a dedicated aircraft-tracking station.

See on Amazon →

Discone antenna

A wideband outdoor antenna that covers aircraft, ham, weather radio and more in one mast.

See on Amazon →

1090 MHz ADS-B antenna

Tuned for aircraft tracking. Mount it high, outdoors if you can.

See on Amazon →

Low-loss SMA extension cable

Lets you put the antenna in a window or outside while the dongle stays at the computer.

See on Amazon →

Avoid the cheapest no-name “TV tuner” sticks. They drift, run hot and often can’t reach the frequencies above. The RTL-SDR Blog V4 is the safe pick, and its maker keeps an excellent V4 user guide.

Free, open-source software

Windows · macOS · Linux · Android

SDR++

Our top pick. Fast, clean and beginner-friendly, and it supports the RTL-SDR Blog V4.

macOS · Linux

Gqrx

A simple, reliable receiver app that has been around for years. Great on a Mac.

Windows · macOS · Linux · Android

SDRangel

A power-user toolbox with built-in decoders for aircraft, ships, APRS, digital voice and more.

Android

RF Analyzer

A free and open-source spectrum analyzer and receiver, available on F-Droid.

Any browser, including iPhone

OpenWebRX+

Runs on a Raspberry Pi with your dongle and puts the receiver in a web page, so you can listen from any phone, tablet or computer on your network.

Windows (free, not open source)

SDR#

You will see SDR# (SDRSharp) in many tutorials. It is free to download but not open source.

Getting started on each platform

First, on every platform: attach the antenna before plugging in, extend the dipole arms to about 75 cm (30 inches) each for general listening, and put it near a window.

Windows

  1. Download SDR++ from its releases page (the Windows x64 zip) and unzip it to a folder.
  2. Install the USB driver once with Zadig: plug in the dongle, open Zadig, choose Options → List All Devices, select Bulk-In, Interface (Interface 0), make sure the target says WinUSB, and click Replace Driver. Skip this and Windows will treat the stick as a TV tuner.
  3. Open SDR++, choose RTL-SDR as the source, and press the play button.
  4. Tune something easy: type 89.300.000 in the frequency box and pick WFM for 89.3 The Current, or 162.550.000 with NFM for NOAA Weather Radio from the Twin Cities.

macOS

  1. Download SDR++ (macOS build) from its releases page, or Gqrx. No driver is needed on a Mac.
  2. Open it. If macOS says the app can’t be checked, right-click (or Control-click) the app and choose Open, then confirm.
  3. Pick the RTL-SDR as the device (in Gqrx it shows up in the first-run window), press play, and tune 89.3 MHz in WFM mode to test.
  4. Use the latest versions. The newer V4 dongle needs up-to-date software; older releases may not recognize it.

Android

  1. Get a USB-OTG adapter (USB-C to USB-A) so the dongle can plug into your phone.
  2. Install an app: RF Analyzer from F-Droid, or the SDR++ Android APK from its releases page (you will need to allow installs from your browser).
  3. Plug in the dongle and allow the app to use the USB device when asked.
  4. Tune and listen. The dongle draws real power, so expect faster battery drain.

iPhone and iPad

Apple doesn’t let apps use these USB radios directly, so the trick is to listen through another device:

  1. Use a Raspberry Pi as your receiver. Plug the dongle into a Pi running OpenWebRX+, then open its web page in Safari. You get a full waterfall and audio on your iPhone, from anywhere in the house.
  2. Or borrow someone else’s radio. Public web receivers such as WebSDR and KiwiSDR let you tune shortwave and ham bands around the world in a browser, with no hardware at all.

Projects to try

Track planes over Saint Paul

Aircraft broadcast their position on 1090 MHz. With a Raspberry Pi and the free ADSB.im image you get a live map of flights around MSP, and you can share data with ADS-B Exchange or FlightAware.

Read your neighbors’ weather stations

rtl_433 decodes hundreds of wireless thermometers, rain gauges and tire sensors on 433 and 915 MHz, and can feed Home Assistant.

Download images from weather satellites

Russia’s Meteor-M satellites send pictures of Earth on 137 MHz. SatDump turns a pass overhead into a cloud image of the Upper Midwest.

Watch the river traffic

Towboats and some barges on the Mississippi send AIS position reports on 162 MHz. AIS-catcher plots them on a map.

Listen to the airport and the hams

Aircraft use AM voice from 118 to 137 MHz. Local ham repeaters are on 2 m and 70 cm (see Ham radio), and Dire Wolf decodes APRS on 144.390 MHz.

See the mesh

Tune 902–928 MHz and watch LoRa “chirps” from Meshtastic and MeshCore nodes sweep across the waterfall. A great way to check whether your node is actually transmitting.

Public safety scanning

Minnesota agencies use the ARMER trunked radio system. SDRTrunk can follow unencrypted talkgroups; many are encrypted and can’t be heard.

Hear the hydrogen line

With a small dish or horn antenna and an amplifier, an RTL-SDR can detect hydrogen in the Milky Way at 1420 MHz. Real radio astronomy from a backyard.

DIY antennas

The included dipole is a good start, but simple homemade antennas can do even better for one job:

Other ways to go further: run the dongle on a Raspberry Pi as an always-on station, use an rtl_tcp server to listen remotely, or add a filtered amplifier (LNA) for weak signals like satellites.